Bolidozor wiki

You've loaded an old revision of the document! If you save it, you will create a new version with this data.

====== Antennas for Bolidozor network ======

Antenna is the first signal input to a [[en:rmds|radio detection sattion]]. It is therefore necessary not to neglect its choice as a signal that is not received cannot be processed. A typical radio antenna receives not only meteor reflections, but also other radio signals - thus, the location of antenna is of high importance and should be chosen carefully. Suitable antenna characteristics can make the choice of location easier and can improve the overall antenna gain. Advantageous are following parameters:

* Sensitivity in the upper hemisphere with respect to observation site. 
  * High efficiency.
  * Insensitivity to signal linear polarisation angle.
  * Suppression of unwanted signals reception from vely low elevations (usually ground noise).

===== Plastic 1/4 lambda GroundPlane =====

{{:cs:antennas:bolidozor_gp_antenna.jpg?600| GP anténa pro síť Bolidozor}}

It represents the basic antenna, currently used on most of our stations. It has an advantage of having small size and it is thus not difficult to install it on balcony, terrace, etc. Equally important is its relatively primitive design which allows for an easy construction suitable for beginners.

A disadvantage is a low gain and a a radiation characteristic that has a sharp zero in zenith (meaning a very bad detection of meteors flying over the observation site, causing, subjectively, a big difference compared to visual observation).

[[en:gpant|A more detailed description]].

===== Helices - QHA =====

SC-QHA Helix is a type of circularly polarised antenna whose parameters can be almost homogenous 	over the whole hemisphere. The antenna is tuned mainly by a proper phasing of its four powering points.

Bolidozor network would make use of a Helix design with a square ground area measuring 2x2m. Such constructions has an advantage compared to a standard self-phase QHA antenna in that it has a narrower receiver bandwidth and greater total efficiency.

[[en:qha|A more detailed description]].
 
===== Patch antenna with a circular polarisation =====

This antenna was designed to improve the gain of the receiving system compared to a currently used GroundPlane antenna. Patch antenna does not have the zero in zenith and has an almost hemispherical radiation characteristics - that is why it is also sensitive to signals from objects flying directly over the observation site. Symmetric shape of radiation pattern (?? vyzařovací charakteristika) is also suitable for phase antennae fields, where there is necessary to optimise the sensitivity of antennae system for a specific type of observation.

The following photos show the first build functional sample of a new patch antenna.

=== Parameters ===

Na funkčním vzorku bylo měřeno přizpůsobení můstkovou metodou. (??)

* A way how to place a preamplifier is not solved
  * The constructions is difficult to be implemented (e.g. it needs to even out a coiled mesh)
  * It is not mechanically stable
  * A way how to tune the antenna is not yet resolved

Patch type antennae with a circular polarisation are difficult to manufacture, because for their function they need a good tuning of the phase shift of two orthogonal linear polarisations - achieved by a deformation and a change in geometrical size of an antenna radiator. Thus it follows that it is easy to detune an antenna by a resonator deformation or a change in dielectric parameters of an environment between a radiator and a reflector. The construction of this antenna type is therefore apparently overcome by SC-QHA antenna type.

===== Other types of antennas =====

An interesting antenna design, that should solve the drawbacks of GP antennas is so-called [[http://on6wg.pagesperso-orange.fr/Doc/Antenne%20Eggbeater-Engl-Part1-Full.pdf|eggbeater]] or an antenna of [[http://en.wikipedia.org/wiki/Turnstile_antenna|Turn style]] type.

A pair of crossed dipoles above a conducting plane could also result in interesting experimental solutions as it would be probably possible to integrate the amplifier directly into the antenna. The resulting active antenna would have better noise parameters and reliability compared to design with separated GP antenna and LNA.

[[http://en.wikipedia.org/wiki/Discone_antenna|Discone antena]] has also be tested for receiving the reflected signal. Although it works, it has an disadvantage of high bandwidth, that causes a penetrations of undesirable signals.

===== Installation of antenna's preamplifier  =====

==== Preamplifier LNA01A ====

A good quality preamplifier is essential due to loses during signal propagation via antenna and due to low intensities of reflected signal.

[[http://www.mlab.cz/Modules/CommRF/LNA01A/LNA01A_Bottom_Small.JPG|LNA01A]] is a preamplifier designed for meteor detection in 2m band. Its benefit is mainly in amplification of signal from antenna (thus decreasing the influence of antenna’s lead (?? svod antény) and the noise from receiver). Furthermore it reduces complications connected to signal radiation from receiver’s oscillator.

Preamplifier is therefore always installed in the immediate proximity of antenna in an plastic waterproof wiring box.

==== Modelling tools ====

* [[http://www.qsl.net/kd2bd/splat.html|RF Signal Propagation, Loss, And Terrain analysis tool for the electromagnetic spectrum between 20 MHz and 20 GHz.]]
  * [[http://en.wikipedia.org/wiki/Numerical_Electromagnetics_Code|NEC2 software]]
  * [[https://github.com/BogdanDIA/nec2-array|Antenna field in v NEC2]]

Please fill all the letters into the box to prove you're human. M P H Z H Please keep this field empty:

Edit summary

Note: By editing this page you agree to license your content under the following license: GNU Free Documentation License 1.3