en:qha
Differences
This shows you the differences between two versions of the page.
Last revisionBoth sides next revision | |||
en:qha [2019/03/18 21:48] – created fluktuacia | en:qha [2019/03/19 15:04] – fluktuacia | ||
---|---|---|---|
Line 23: | Line 23: | ||
===== Construction ===== | ===== Construction ===== | ||
- | Structural parts of the antenna are primarily made of galvanised steel components. Those parts, which are under a higher current load are made of copper | + | Structural parts of the antenna are primarily made of galvanised steel components. Those parts, which are under a higher current load are made of copper |
Antenna’s dimensions were optimised using a [[https:// | Antenna’s dimensions were optimised using a [[https:// | ||
Line 32: | Line 32: | ||
* Helix height : 312.2 mm (angle of inclination 27 degrees) | * Helix height : 312.2 mm (angle of inclination 27 degrees) | ||
* Cutting length of upper cross (??Řezná) : 369.9 mm | * Cutting length of upper cross (??Řezná) : 369.9 mm | ||
- | * Cutting | + | * Cutting |
==== Material ==== | ==== Material ==== | ||
- | Fázovací | + | Phasing lines (?? fázovací |
+ | Antenna helix is made of copper tubes with outer diameter of 18 mm. The tubes are made of ‘soft’ copper, used in air-conditioning units installations. They are available in reel that makes it much easier to construct the antenna. | ||
- | Šroubovice antény je tvořena měděnými trubkami o vnějším průměru 18mm. Jde o " | + | {{: |
- | {{: | ||
+ | * 400x Galvanized | ||
- | * 400x Pozinkovaný trhací nýt 4.8x10 mm | ||
- | * | ||
- | z==== Výroba | + | ==== Construction |
- | {{: | + | {{: |
- | Anténa se skládá ze čtyř kusů základnových čtverců sloužících, | + | The antenna is made of four pieces of base squares that serve as a universal ground potential. These squares are screwed together at each side by a four M8 screws. There is a fan washer (?? vějířová podložka) at both sides of the screw. A reason for this is a better conductivity of connection and, at the same time, better prevention against a spontaneous loosening during manipulation with antenna. |
- | {{: | + | {{: |
- | Zkratovací kříž na vrcholu helixu je sletován ze 3kusů trubek z " | ||
- | Kříž | + | Zkratovací kříž |
- | {{: | + | The cross is thus made of one longer tube with two shorter ones soldered perpendicularly to it. The shorter tubes have their walls pierced, so they fit precisely to the longer tube. It is also necessary to keep the sum of the lengths of the tubes such, that both arms of the cross measure 370 mm. |
+ | {{: | ||
- | ===== Naměřené charakteristiky ===== | ||
- | Na sestavené anténě bylo měřeno přizpůsobení antény. K měření byl použit spektrální analyzátor DSA815-TG s [[http:// | + | ===== Measured characteristics ===== |
- | {{:cs: | + | The assembled antenna underwent a measurement of adaptation (přizpůsobení antény) using a spectral analyser DSA815-TG with [[http://www.ebay.com/ |
+ | {{: | ||
+ | The antenna is sensitive to the way of connecting the phasing lines. Two basic possibilities can be seen on the following pictures. They differ in the direction of the | ||
Anténa je citlivá na způsob připojení fázovacího vedení. Dvě základní možnosti jsou vidět na následujících obrázcích, | Anténa je citlivá na způsob připojení fázovacího vedení. Dvě základní možnosti jsou vidět na následujících obrázcích, | ||
en/qha.txt · Last modified: 2019/03/20 16:59 by fluktuacia